Cursor/board combination
(Difference between revisions)
(→A201) |
(→A201) |
||
Line 13: | Line 13: | ||
| 02 || 2 || 02 || 2 || 22 || yes || 1/1 || 1/1 || || | | 02 || 2 || 02 || 2 || 22 || yes || 1/1 || 1/1 || || | ||
|- | |- | ||
− | | 03 || 3 || 13 || 3 || 23 || yes || 1/1 || 1/1 || | + | | 03 || 3 || 13 || 3 || 23 || yes || 1/1 || 1/1 || fabien Currit Nicolas Schnyder || |
|- | |- | ||
| 04 || 4 || 14 || 4 || 20 || yes || 1/1 || 1/1 || || LCD board 24 missing <br /> LEDs not shining (possibly flipped) <br /> button order flipped on LCD board 20 | | 04 || 4 || 14 || 4 || 20 || yes || 1/1 || 1/1 || || LCD board 24 missing <br /> LEDs not shining (possibly flipped) <br /> button order flipped on LCD board 20 |
Revision as of 09:26, 10 December 2018
|
A201
Number | Cursor | FPGA Board | Programmer | LCD Board | EEPROM Programmed | Power cable large/small |
Ribbon cable long/short |
Group Members | Comment |
---|---|---|---|---|---|---|---|---|---|
01 | 1 | 03 | x | 21 | yes | 1/1 | 1/1 | ||
02 | 2 | 02 | 2 | 22 | yes | 1/1 | 1/1 | ||
03 | 3 | 13 | 3 | 23 | yes | 1/1 | 1/1 | fabien Currit Nicolas Schnyder | |
04 | 4 | 14 | 4 | 20 | yes | 1/1 | 1/1 | LCD board 24 missing LEDs not shining (possibly flipped) button order flipped on LCD board 20 | |
05 | 5 | 15 | 5 | 25 | yes | 1/1 | 1/1 | LEDs not shining (possibly flipped) | |
06 | 6 | 06 | 6 | 26 | yes | 1/1 | 1/1 | Hall sensors not working | |
07 | 7 | 07 | 7 | 27 | yes | 1/1 | 1/1 |
A203
Number | Cursor | FPGA Board | Programmer | LCD Board | EEPROM Programmed | Power cable large/small |
Ribbon cable long/short |
Group Members | Comment |
---|---|---|---|---|---|---|---|---|---|
11 | 11 | 41 | 21 | 31 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
12 | 12 | 42 | 22 | 32 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
13 | 13 | 43 | 23 | 33 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
14 | 14 | 44 | 24 | 34 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
15 | 15 | 45 | 25 | 35 | yes | 1/1 | 1/1 | Cursor not working (verifying encoder signals) | |
16 | 16 | 46 | 26 | 36 | yes | 1/1 | 1/1 | Cursor not working (verifying encoder signals) | |
17 | 17 | 47 | 27 | 37 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
18 | 18 | 48 | 28 | 38 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
19 | 19 | 49 | 29 | 39 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
20 | 20 | 50 | 30 | 30 | yes | 1/1 | 1/1 | ok (12.11.2018) | |
21 | 21 | 51 | 10 | 24 | no | 1/1 | 1/1 | Error initializing chain (cursor tested with board 50: motor blocks sometimes during ramp) | |
08 | 58 | 08 | 28 | yes | 1/1 | 1/1 | - - | ok (12.11.2018) | |
09 | 59 | 09 | 29 | yes | 1/1 | 1/1 | - - | ok (12.11.2018) |