HiRel/CanSat/Slave XBee
(Difference between revisions)
Line 8: | Line 8: | ||
|- | |- | ||
|} | |} | ||
− | |||
The [[HiRel/CanSat|CanSat]] RF communication is done with the help of an | The [[HiRel/CanSat|CanSat]] RF communication is done with the help of an | ||
[http://www.digi.com/products/model?mid=3588 XBee-PRO ZB S2B module w/ U.Fl antenna connector]. | [http://www.digi.com/products/model?mid=3588 XBee-PRO ZB S2B module w/ U.Fl antenna connector]. | ||
+ | |||
+ | = Connection = | ||
The connection to the module is done through following pins: | The connection to the module is done through following pins: | ||
Line 34: | Line 35: | ||
| sleep_n || t7 || out || sleep indicator | | sleep_n || t7 || out || sleep indicator | ||
|} | |} | ||
+ | |||
+ | = Setup = | ||
An XBee module can work in API mode, providing a complete ZigBee network, or as a simple AT modem. | An XBee module can work in API mode, providing a complete ZigBee network, or as a simple AT modem. | ||
In order to communicate between different modules, a common PAN identifier must be set. | In order to communicate between different modules, a common PAN identifier must be set. | ||
The [[Media:Xbee-product-manual.pdf|XBee product manual]] gives the setup information. | The [[Media:Xbee-product-manual.pdf|XBee product manual]] gives the setup information. | ||
+ | |||
+ | The module can be configured via a serial or [http://ftp1.digi.com/support/documentation/xbibudev_referenceguide.pdf USB programmer board] | ||
+ | with the [http://www.digi.com/products/wireless-wired-embedded-solutions/zigbee-rf-modules/xctu XCTU] application. | ||
+ | |||
+ | The serial port setup is: | ||
+ | * 115200 baud | ||
+ | * 8 bit, no parity | ||
[[Category:Master]] [[Category:HiRel]] [[Category:CanSat]] | [[Category:Master]] [[Category:HiRel]] [[Category:CanSat]] |
Revision as of 10:45, 29 May 2015
|
Type | CanSat Slave XBee | Schematic | Description |
---|---|---|---|
V1.0 | CanSat Slave XBee v1.0 Schematic PDF | XBP24BZ7UIT-004 |
The CanSat RF communication is done with the help of an XBee-PRO ZB S2B module w/ U.Fl antenna connector.
Connection
The connection to the module is done through following pins:
name | pin | dir | description |
---|---|---|---|
data_in | b2 | in | serial link RxD |
data_out | b4 | out | serial link TxD |
reset_n | b6 | in | reset_n |
sleep_rq | b8 | in | sleep control |
RSSI_PWM | t1 | out | radio signal strength indication |
associate | t3 | out | association indication |
dio | t5 | inout | digital I/O |
sleep_n | t7 | out | sleep indicator |
Setup
An XBee module can work in API mode, providing a complete ZigBee network, or as a simple AT modem. In order to communicate between different modules, a common PAN identifier must be set. The XBee product manual gives the setup information.
The module can be configured via a serial or USB programmer board with the XCTU application.
The serial port setup is:
- 115200 baud
- 8 bit, no parity