HiRel/CanSat/Slave XBee

(Difference between revisions)
Jump to: navigation, search
Line 8: Line 8:
 
|-
 
|-
 
|}
 
|}
 
  
 
The [[HiRel/CanSat|CanSat]] RF communication is done with the help of an
 
The [[HiRel/CanSat|CanSat]] RF communication is done with the help of an
 
[http://www.digi.com/products/model?mid=3588 XBee-PRO ZB S2B module w/ U.Fl antenna connector].
 
[http://www.digi.com/products/model?mid=3588 XBee-PRO ZB S2B module w/ U.Fl antenna connector].
 +
 +
= Connection =
  
 
The connection to the module is done through following pins:
 
The connection to the module is done through following pins:
Line 34: Line 35:
 
| sleep_n || t7 || out || sleep indicator
 
| sleep_n || t7 || out || sleep indicator
 
|}
 
|}
 +
 +
= Setup =
  
 
An XBee module can work in API mode, providing a complete ZigBee network, or as a simple AT modem.
 
An XBee module can work in API mode, providing a complete ZigBee network, or as a simple AT modem.
 
In order to communicate between different modules, a common PAN identifier must be set.
 
In order to communicate between different modules, a common PAN identifier must be set.
 
The [[Media:Xbee-product-manual.pdf|XBee product manual]] gives the setup information.
 
The [[Media:Xbee-product-manual.pdf|XBee product manual]] gives the setup information.
 +
 +
The module can be configured via a serial or [http://ftp1.digi.com/support/documentation/xbibudev_referenceguide.pdf USB programmer board]
 +
with the [http://www.digi.com/products/wireless-wired-embedded-solutions/zigbee-rf-modules/xctu XCTU] application.
 +
 +
The serial port setup is:
 +
* 115200 baud
 +
* 8 bit, no parity
  
 
[[Category:Master]] [[Category:HiRel]] [[Category:CanSat]]
 
[[Category:Master]] [[Category:HiRel]] [[Category:CanSat]]

Revision as of 10:45, 29 May 2015

Contents

Type CanSat Slave XBee Schematic Description
V1.0 CanSat Slave XBee V1.0 CanSat Slave XBee v1.0 Schematic PDF XBP24BZ7UIT-004

The CanSat RF communication is done with the help of an XBee-PRO ZB S2B module w/ U.Fl antenna connector.

Connection

The connection to the module is done through following pins:

XBee I/O connections
name pin dir description
data_in b2 in serial link RxD
data_out b4 out serial link TxD
reset_n b6 in reset_n
sleep_rq b8 in sleep control
RSSI_PWM t1 out radio signal strength indication
associate t3 out association indication
dio t5 inout digital I/O
sleep_n t7 out sleep indicator

Setup

An XBee module can work in API mode, providing a complete ZigBee network, or as a simple AT modem. In order to communicate between different modules, a common PAN identifier must be set. The XBee product manual gives the setup information.

The module can be configured via a serial or USB programmer board with the XCTU application.

The serial port setup is:

  • 115200 baud
  • 8 bit, no parity
Personal tools
Namespaces
Variants
Actions
Navigation
Modules / Projects
Browse
Toolbox