Kart

(Difference between revisions)
Jump to: navigation, search
(Power supply)
(Components)
Line 117: Line 117:
 
Finally, an ADC converter provides the [[kart/battery level|battery level]] as both the battery voltage and consumed current can be read from it.
 
Finally, an ADC converter provides the [[kart/battery level|battery level]] as both the battery voltage and consumed current can be read from it.
  
=== FPGA boards ===
+
=== FPGA board ===
  
The [[Kart/FPGA board|FPGA motherboards]] are equipped with an AGL125 [http://www.microsemi.com/products/fpga-soc/fpga/igloo-overview IGLOO] in a VQ100 package. The clock passed to the FPGA comes from a 10 MHz quartz.
+
The [[Kart/Daughterboard|daughterboard]] is equipped with an [https://www.mouser.ch/datasheet/2/268/Microsemi_DS0110_IGLOO_nano_Low_Power_Flash_FPGAs_-1592764.pdf Igloo AGLN250] FPGA in a VQ100 package.
 +
The clock is rooted to the FPGA from a 10 MHz quartz.
  
They hold daughterboards which drive different parts of the Kart.
+
It is designed as an SODIMM-200 RAM stick to be easily interchangeable and plugged into various motherboards.
The motherboards are interconnected via an [[kart/I2C link|I2C link]].
+
 
+
The FPGA motherboards can be tested with the help of a dedicated [[Kart/FPGA_board#Test|test board]] which runs a signal from one I/O pin to the next.
+
 
+
=== FPGA daughterboards ===
+
 
+
Existing daughterboards are:
+
* a [[Kart/Bluetooth|Bluetooth interface board]]
+
* a [[Kart/DC motor controller|DC motor controller]]
+
* a [[Kart/stepper motor controller|stepper motor controller]]
+
* an [[Kart/sensor board|I/O board]] for the sensors
+
* an [[Kart/FPGA_board#Test|FPGA test]] board
+
  
 
=== Sensors ===
 
=== Sensors ===
  
The sensors connected to the I/O board are:
+
The sensors connected to the I/Os of the motherboard are:
* 1 to 4 [[kart/sensors/VCNL4000|VCNL4000 I2C Distance/Ambience Light Sensor]]
+
* 0 to 4 [[kart/sensors/VCNL4000|VCNL4000 I2C Distance/Ambience Light Sensor]]
 
* 1 to 2 [[kart/sensors/SS311PT|SS311PT Hall Sensor]]
 
* 1 to 2 [[kart/sensors/SS311PT|SS311PT Hall Sensor]]
 
* 1 [[Kart/sensors/HCSR04|ultrasound ranger]]
 
* 1 [[Kart/sensors/HCSR04|ultrasound ranger]]

Revision as of 09:54, 27 June 2022

Contents

The Kart module (214_Pr1) is a Summer School module for students between the 2nd and the 3rd semester. It is a home-made model car remotely controlled by a smartphone.

Demo Kart

The work of the students can be summarized in four main tasks:

Take a look at the karts gallery !

System Architecture

The kart is controlled by a smartphone via Bluetooth.

Hardware

The electronic is composed of an FPGA daughterboard which embedds an Igloo AGLN250 chip. It is designed as an SODIMM-200 RAM stick to be plugged into the motherboard, where all sensors and control boards are wired through the PMOD standard as well as the battery and an I2C chip to read both the battery voltage and consumed current.

An Honor10 Lite running Android acts as the interface for the user.

Distributed controls

A Bluetooth - USB dongle on the kart communicates via an UART serial link with the FPGA. The control values are stored in a set of registers accessed through a simple protocol.

The design is separated over four different modules:

Tasks

The programming introduction gives an overview about the structure of the software/hardware and the students' tasks. They comprise:

  • FPGA design for driving the hardware and reading the sensors
  • Android application development for the remote control

The students receive the FPGA board preprogrammed with a functional solution and Android phones with a demo application. This allows to start the development either with the FPGA design or the Android application.

FPGA Design

Design environment

A FPGA design environment is available, based on:


View-pim-tasks.png

clone the Git repository or download the corresponding zip and install it, preferably to your personal drive (U:\).

Dialog-warning.png

Make sure that there is no space character in the path to ELN_kart.

The design is made using HDL Designer as it was the case during the case during the previous semester's labs and project. The FPGAs are configured using the Libero IDE.

Modules designs

Three of the different modules must be completed:

  • The DC motor controller receives a prescaler and a speed value to build the corresponding PWM and direction signals.
  • The stepper motor controller receives a prescaler and the desired angle and builds the coil controls signals.
  • The sensor controller manages I/O comprising hall sensors (to retrieve the driving speed) and a range finder (to get the distance from an obstacle).

Android App

One goal is to implement an Android application that controls and monitors the kart.

Introduction

The installable package of the (or rather a) solution can be found here: Kart.apk

Starting point

  • You can download the Kart project with the minimal interface here: Kart.zip
  • You can find the instructions how to open the project in Android Studio in the programming introduction presentation...
  • The online documentation of all Java classes that are at your disposition is [here]
  • If you need timers, please do not use Java standard Timer and TimerTask, we provide a dedicated Timer class in the package ch.hevs.utils.Timer.
  • To be informed when a register is modified by the kart (i.e. the hall sensor counter value has changed), your application has to implement the KartStatusRegisterListener interface. This will force your application to have a method (statusRegisterHasChanged) that will be called when a register value has changed. Don't forget to register your listener to the Kart (kart.addStatusRegisterListener(...)).

Common Problems

  • Don't block the main thread with an infinite loop
  • Don't change the orientation of the display during the execution, it can crash the BT communication. Do it in the Manifest.

Virtual Kart

If you need to test your Android application against a Kart and your Kart is either not build yet or not available at the moment, you can install the Virtual Kart application and use the Kart Bluetooth to USB adapter board.

  • Windows version here
  • macOS version here

Components

Power supply

The main power is drawn from two 6 V / 2400 mAh battery packs in series The motherboard provides two connectors for the batteries, along with an extra one to wire an NiMh charger.

Dialog-warning.png

Make sure to shut the circuit off while charging to avoid higher voltage on the 12V rail.

The charge rate should be of around 0.05C => 120mA here.

The 12V is then reduced to a 5V rail through a buck converter. The daughterboard is then fed with the 5V to provide an extra 3.3V rail.

Finally, an ADC converter provides the battery level as both the battery voltage and consumed current can be read from it.

FPGA board

The daughterboard is equipped with an Igloo AGLN250 FPGA in a VQ100 package. The clock is rooted to the FPGA from a 10 MHz quartz.

It is designed as an SODIMM-200 RAM stick to be easily interchangeable and plugged into various motherboards.

Sensors

The sensors connected to the I/Os of the motherboard are:

Additional Information

Personal tools
Namespaces
Variants
Actions
Navigation
Modules / Projects
Browse
Toolbox