Inverter
(→FPGA board) |
(→FPGA board) |
||
Line 72: | Line 72: | ||
The main board is the school's [http://wiki.hevs.ch/uit/index.php5/Hardware/FPGAEBS FPGA-EBS lab development board]. | The main board is the school's [http://wiki.hevs.ch/uit/index.php5/Hardware/FPGAEBS FPGA-EBS lab development board]. | ||
It hosts a [http://www.xilinx.com/products/silicon-devices/fpga/spartan-3.html Xilinx Spartan xc3s500e FPGA] and features many different interfaces. | It hosts a [http://www.xilinx.com/products/silicon-devices/fpga/spartan-3.html Xilinx Spartan xc3s500e FPGA] and features many different interfaces. | ||
− | The clock oscillates at 66& | + | The clock oscillates at 66 MHz. |
=== Buttons and LEDs I/O board === | === Buttons and LEDs I/O board === |
Revision as of 11:35, 27 November 2017
|
The Filière Energie et Techniques environnementales (FET) has the digital systems course and labs in the 3rd (autumn) semester. The semester counts 15 weeks and ends with a little project. The aim of the inverter project is to generate a 50 Hz AC power supply from a DC input.
Specification
Function
The 12 V power supply is chopped by the power switches of an H-bridge in order to generate a sine wave. The resulting voltage is filtered by a passive LC filter to provide a smooth sine wave. The digital system generates the PWM controls of the 4 power switches.
An I/O board with 4 switches and 8 LEDs allows to control the operating mode and to display information about the system's state.
PWM modes
Different PWM modes are to be investigated:
- a two-level mode with inverted controls on each H-bridge branch
- three-level modes with separate controls on each branch
Output
The system has to generate a 110 VAC power supply.
This is achieved with the help of a transformer. This transformer:
- provides ah high enough voltage amplitude to allow the generation of a 110 VAC output from a 12 power supply
- transforms a differential signal into a floating one, allowing a simple measurement.
As the output voltage is high, great care has to be taken with the transformer output side.
Components
The system consists of
- an H-bridge power board together with a power LC lowpass board
- a transformer board
- an FPGA prototyping board
- an buttons and LEDs I/O board for the control
- a logic-level LC lowpass board
H-bridge power board
The H-bridge board is powered with 12 V. The 4 MOS transistors are driven by 2 IR2110 driver circuits. The PWM controls are brought to the board via a ribbon cable.
This board is also used for an audio amplifier student project.
The 12 V power supply from this board is brought to the ribbon cable connector and is used to power the FPGA board as well.
Power LC lowpass board
The LC lowpass board is used in conjunction with the H-bridge power board. It smooths the PWM signal into a sine wave.
The default LC cutoff frequency is something like 20 kHz, as this board is also used for an audio amplifier.
Transformer board
The transformer board allows to reference the differential output to any common voltage.
The board at our disposal transforms 7.5 V to 115 V. As it provides a high voltage, it should be handled with great care.
FPGA board
The main board is the school's FPGA-EBS lab development board. It hosts a Xilinx Spartan xc3s500e FPGA and features many different interfaces. The clock oscillates at 66 MHz.
Buttons and LEDs I/O board
The buttons and LEDs board is used in conjunction with the FPGA board.
It has 4 buttons and 8 LEDs. It can hold an optional LCD display.
Logic-level LC lowpass board
The logic-level LC lowpass board is used to verify the content of the PWM signals in the two H-bridge branches. It smooths the two FPGA output PWM signals into the components of a differential sine wave.
On this board too, the default LC cutoff frequency is something like 20 kHz.
Getting started
In order to start the projects you should do the following:
- Read carefully the specifications above
- Draw the architecture of the circuit in the form of a block diagram
- Consult the guides for the first steps into the design software
Additional Information
- Board combinations
- Additional informations for teachers.