Search results

Create the page "Mezzanine" on this wiki!

• Hardware/Beckhoff FB1130
  * 2 50Pin HESSO Mezzanine connection (compatible with FPGA-EBS, FPGA-Rack, ARM-EBS) * Power Supply through connector or Mezzanine
  2 KB (259 words) - 07:53, 20 September 2013
• Hardware/Stock Altera FPGA
  ...ce FPGA|up=Inventory|up_name=Inventory|right=Hardware/Stock_Mez|right_name=Mezzanine}}
  2 KB (171 words) - 09:51, 27 November 2017
• Hardware/Stock PP
  * added connector for AudioAmp Mezzanine Input {{navNamed|left=Hardware/Stock_Mez|left_name=Mezzanine|up=Inventory|up_name=Inventory|right=Hardware/Stock_Backplane|right_name=Ra
  15 KB (863 words) - 09:14, 6 December 2019
• Hardware/Parallelport/Audio ADC DAC
  * Connect Mezzanine Audio Adapter board * Power the FPGA via the Mezzanine connector
  2 KB (376 words) - 06:35, 21 August 2014
• Projects/Envirobot
  Currently there exist two setups, one with about 2 cm between the mezzanine and the cover and the other one with about 6.5 cm. If the sensor needs anot ...ith other levels, a level translation circuit has to be implemented on the mezzanine board.
  7 KB (1,087 words) - 15:26, 31 July 2017
• Hardware/FPGARack4ethernet
  {{WarningBox|content=Mezzanine Pin <code>T8</code> - <code>MEZ_PB19</code> can't be used if a ''XC6SLX100' * 2 Mezzanine Connector ARM-EBS and FPGA-EBS compatible
  5 KB (731 words) - 10:42, 12 December 2016
• Hardware/Mezzanine/PWM
  [[Category:Hardware]] [[Category:Mezzanine]] [[Category:HEB]]
  441 B (60 words) - 13:13, 18 January 2018
• Hardware/FPGARackHiRADDAV1
  ...e]]. Additional specific hardware can be connected to HiRADDA as stackable mezzanine card.
  9 KB (1,395 words) - 09:20, 28 March 2018

• File:Envirobot SensorCtrl MezzConductivity.png Sensor Control Board with Sensor Mezzanine with Conductivity Electronics and Temperature Sensor mounted in Sensor Comp (1,383 × 829 (2,785,030 bytes)) - 08:03, 15 October 2015

• Hardware/MiniBioDet
  The MiniBioDet is composed of two board : the mother-board and a mezzanine. the mezzanine contains the analog front-end as well as the application specific connector
  2 KB (374 words) - 21:30, 18 March 2016
• Inventory/EDAbox
  * C-shaped mezzanine
  3 KB (409 words) - 09:44, 2 August 2018
• Hardware/Stock FPGA-EBS
  | 50 || || || 2018-02: added Mezzanine connector <br/> 2015: PCM1804 and PCM1793 replaced <br/> 2019/11: FPGA repl | 51 || || || 2018-02: added Mezzanine connector <br/> 2019/11: FPGA replaced
  7 KB (560 words) - 07:33, 10 March 2020
• Projects/CubeSatCom/Meetings
  ** one mezzanine complete, ready to test whole setup, rest will be mounted this week ** PCBs rack done, mezzanine end of week
  13 KB (1,910 words) - 15:30, 21 August 2017
• Projects/CubeSatCom/EngineeringModel
  ...a Xilinx Spartan 6 FPGA and the VME compatible connector with 3x32 Pins. A mezzanine holding an MSP430 has been developed. The MSP430 is used to configure and c ...up bases on the control of the system by a microprocessor on the FPGA rack mezzanine.
  3 KB (458 words) - 17:16, 22 March 2018
• Inventory/Signal/AudioAmplifier
  == [[Hardware/Mezzanine/PWM|Audio Amplifier - Mezzanine]] ==
  2 KB (155 words) - 09:34, 28 September 2018
• Hardware/FPGAPoetic
  ...NGRW project in addition with the [[Hardware/Mezzanine/Poetic|FPGA ADC-DAC Mezzanine]]. * 2 Mezzanine Connector ARM-EBS and FPGA-EBS compatible
  2 KB (282 words) - 13:50, 12 July 2022
• Hardware/Mezzanine/Poetic
  This mezzanine was developped for the FPGA Poetic Board during [https://gitlab.hevs.ch/the The mezzanine board has 8 SMA connectors (DAC output), 2 connectors 2x10 pins (ADC input)
  1 KB (152 words) - 12:00, 1 October 2021